Linux Training for People New to Linux - How to Use Linux Command Line Components by Clyde Boom
Linux Commands - The great thing about Linux commands is that they are virtually identical from one Linux distribution (version) to another. So the way the real pros do Linux administration is to work at the Linux command line and run Linux commands. ... Learning how to run a Linux command can be very difficult for someone new to Linux, so here are some Linux tips that will help you to learn how to use Linux commands when working at the Linux command line prompt. ... The "item(s)" that the Linux command is being run "on" When you run a Linux command, spaces are used between: the Linux...

How To Control The Way Linux Starts Up: GUI or Command Line Interface by George Chamoun
If you were interested in learning linux, one of the main reasons was learning how to work using Linux Shell environment. That is the Command Line Interface ( CLI). How Did I know?. It happened to me, and the most asked Question is how to access the Command line in Linux. ... Here is how you do it: 1-If you are presented with the command line after Linux boots, And after you login and end up at the command line prompt, you Type: STARTX The above command start up the GUI from the command line, and Get you in the Graphic GUI environment of Linux.

Linux Terminal Control Sequences by Bernard Peh
Linux terminals share alot in common with their primitive ancestors such as vt100 like consoles. These early devices is capable of sending sequences that signaled events outside of the normal flow of typed characters, such as escape, tab, linefeed...etc. ... So if you tpye WC at the command prompt, the command will wait for your input till you use CTRL-D to signal the end of transmission. ... For example, if you accidentally run a command that does not stop, use CTRL-C to cancel the command. ... You can later restore back the command using the fg command.

Linux Training - Linux Installation Help - How To Install the Linux OS from a New Linux Download by Clyde Boom
You can install Linux from CD or DVD onto a new computer system. This will allow you to learn how to use Linux to get real, practical Linux training and experience. In this article, we're talking about a new system that doesn't already have an operating system (like Windows) on it. ... Let the Linux OS Install on Your Hard Disk After you specify the Linux installation settings and create one or more new Linux users, the installation routine will copy the Linux OS and Linux software programs onto the hard disk in the system, and then reboot.

How To Automate Tasks In Your Linux Server by Bernard Peh
If your host is running under the Linux (Unix) operating system, you can perform tasks in the server on a regular basis. For example, sending mails at a certain time of the day, backing up database at 6 in the morning and so on. "Cron" is a program that runs in the background of the Linux server. ... The first 5 fields are used to specify when to run the command, and the last field determines what command to run. ... Basically, SSH allows you to type commands in the command prompt. ... For example, if I want to run a php script at 12 midnight everyday, I will type "crontab -e", then write...

Dual Boot Windows and Linux: Single and Multiple Hard Drives by David Picella
The internet is full of technical articles, many of which are way too complicated for the average computer user who just wants to solve a simple problem. If you pay close attention, the internet is also a place where the "gurus" spend a lot of time yelling for help in discussion boards and forums. ... Step 1: Linux From the shell in your Linux installation (boot from your installation disks): Execute the following shell command, replacing /dev/hda3 with the location of your Linux boot partition.

Linux or Windows - Which is it? by J. Brian Keith
Computer users and programmers have become so accustomed to using Windows, even for the changing capabilities and the appearances of the graphical interface of the versions, therefore it has remained Microsoft's product. Although, Lycoris, Red Hat, Mandrake, Suse, Knoppix, Slackware and Lindows... The nature of the Linux GUI makes remote administration of a Linux computer easier with a more natural feel than Windows computers. ... Linux, like UNIX, also supports multiple command interpreters, but it usually uses BASH or "Bourne Again Shell".

Booting Problem in PC by ravi chamria
One fine day you start your PC and get messages that say,”Book Disk failure”. The problem is that the hard disk is detected but the OS does not load. The system may get stuck in the second screen during the booting process or the OS might display an error message and refuse to load. ... Go to the command prompt and give the command fdisfk/mbr’and then give the command ‘sys C’. ... If Lila gets corrupted, you can not boot into either OS.When this happens, you have to boot into the system using some other media, such as a boot floppy or the Windows Dafter booting go to the command prompt,...

Wireless Linux: Using the Linux Wireless ToolBox by Eric Meyer
First thing you need to do is purchase a wireless adapter card with a prism2 chipset. Just go to google and type in linux wireless adapters and track one down. If you are using a fairly good wireless distro it should pick up the card automatically. Ok, Now you have the card now what, you plugged... Now type in iwlist at the command prompt. ... You can enter administrator mode by typing su at the command prompt. ... Type in iwlist at the command prompt. ... Once you have located the access point you want to connect with it' time to start using another command called iwconfig.

Power of the Unix 'for' Loop by Praveen Puri
If you are a programmer or engineer working in a unix or linux environment, you will probably find the shell 'for' loop to be a handy tool for automating command line tasks. Here are three examples of the 'for' loop. All the commands are in italics and should be entered on the command line,... If the file is readable, print the first line, otherwise print an error message: for i in `cat file_list.txt` do if test -r $i then echo "Here is the first line of file: $i" sed 1q $i else echo "file $i cannot be open for reading." fi done Here, we loop...